Hi you 4435 owners!
Could you tell me the thickness of material used for the 4435 cab?
Thanks for help!
Port size is 4.125 inch (10,5 cm) dia and 5 inch (12,7 cm) length. Right?
Hi you 4435 owners!
Could you tell me the thickness of material used for the 4435 cab?
Thanks for help!
Port size is 4.125 inch (10,5 cm) dia and 5 inch (12,7 cm) length. Right?
Come on lazy guys! give me three simple measurements.
Thanks!
36-24-36
Originally posted by Giskard
36-24-36
Do you have a pic also?
Hi Guido,Originally posted by Guido
Do you have a pic also?
If you tell me exactly what you want to know, I can figure it out.
Please let me a few hours if I have to open the cabinet for measurements.
HP
Please help us save more info about the vintage systems. Let us register your speakers and drivers.
Thanks Hans Peter!
I just need the wall thickness of the cab. I think it is made of 25mm wood but I'm not sure.
Then I would like to know if this port size is right:
Port size is 4.125 inch (10,5 cm) dia and 5 inch (12,7 cm) length
I just found out:Originally posted by Guido
Thanks Hans Peter!
I just need the wall thickness of the cab. I think it is made of 25mm wood but I'm not sure.
Then I would like to know if this port size is right:
Port size is 4.125 inch (10,5 cm) dia and 5 inch (12,7 cm) length
port size 104mm dia, 133mm deep, thickness of port material 3,5mm.
Sidewalls are only 19mm !!!. others later (have to put out the woofer......)
HP
Please help us save more info about the vintage systems. Let us register your speakers and drivers.
HP could you please measure the height of the pedestal?
Thanks
Can anybody please do a scan or good picture of the 4435 foilcal?
Thanks
Guido,
I have one that I can scan on a flatbed and I'll put the image in an accessible place. 600dpi tiff?
John
Hi John
I'll PM you my mail adress.
Thanks, 600 dpi tif or jpg is ok!
Hi Guido,Originally posted by Guido
HP could you please measure the height of the pedestal?
Thanks
of cause,...please wait patiently till "after work time"
Tell me which measurements you need too.
HP
Please help us save more info about the vintage systems. Let us register your speakers and drivers.
Hi all,
is there any interest in posting the 4435 complete drawing (from the original) ?
If someone wants to know about the comparision between 43xx and 4435...ask our site admin John Nebel.
HP
Please help us save more info about the vintage systems. Let us register your speakers and drivers.
"is there any interest in posting the 4435 complete drawing (from the original) ?"
Absolutely! I am very interested in drawing up as many of the vintage JBL enclosures as possible.
Hi Guido,Originally posted by Guido
HP could you please measure the height of the pedestal?
Thanks
as requested from Giskard and others which PM'd me, I will post the complete drawings soon.
I will begin with your request for the pedestal......
It's made from solid square wood with 40,5 x 40,5 mm (about 1 1/2"). It's formed like "U" and open to the backside of the cab.
From the front edge (without grille) it's 23mm back, from the sidewalls 25mm.At the backside it ends 3mm before backwall.
more will follow as ACAD file (hope you can read)
BTW: the speaker is built very simple from 19mm chipboard and divided to two chambers exactly in the middle.
HP
Please help us save more info about the vintage systems. Let us register your speakers and drivers.
There are currently 1 users browsing this thread. (0 members and 1 guests)