Results 1 to 15 of 28

Thread: 4435 conversion to TAD2001

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503

    4435 conversion to TAD2001

    I finally finished the modification of the 4435 network for the use of a TAD2001 driver and must say it was worth the work.
    Following I'll post the first real 2426 (Aquaplas coated) - TAD2001 comparison at our forum.
    Finally I'll advice you how to modify the network.

    Feel free to ask questions. It's not to hard to do though

  2. #2
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503

    Response

    First 2426AQPL vs TAD2001 on 2344 on Axis
    Second 2426AQPL vs TAD2001 on 2344 30°

    SPL isn't normalized to 1W/1m My mistake, but who cares? The drivers are more or less of same efficiency.
    Attached Images Attached Images   

  3. #3
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503

    Waterfall

    First 2426AQPL on 2344
    Second TAD2001 on 2344

    The TAD goes way high with incredible nice waterfall.
    The 2426 isn't bad either
    Attached Images Attached Images   

  4. #4
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    Impedance Graphs
    Blue 2426AQPL
    Red TAD2001

    TAD shows similar impedance as 2426 J. Will be compensated with a crossover modification.
    Lower Fs on TAD because of mylar suspension and bigger diaphragm.
    Attached Images Attached Images  

  5. #5
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503

    Schematic - Voltage Drive

    The schematic shows L-Pad values for my prefered adjustment:
    2426AQPL from earlier setup
    TAD2001 from actual listening sessions

    Rpar needed to be changed due to higher impedance of TAD2001
    Resonance circuit (40uH) no longer necessary
    Compensation C changed a bit
    Slight L-Pad adjustment

    Thats all

    Voltage drives are with real impedance, thus a bit wavy.

    Schematic is of course simplified as I use CC crossovers.
    Attached Images Attached Images   

  6. #6
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503

    Result

    The real response is very similar or even identical to the predicted response

    As said, this is my prefered L-Pad adjustment before (2426AQPL) and after (TAD2001) modification.
    Still the L-Pads are in use to make subtle changes.

    Stop lamenting about TAD prices. Go get a pair. The TAD graph looks slightly smoother but can't really show the improvement. It's incredible how this dramatic 4435 low end combined with the TAD top end sounds. Uuuuhhhh
    Attached Images Attached Images  

  7. #7
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    That's all for now.

    Rob I didn't plan to measure new Waterfalls. What do they really tell us? The TAD's will only bring a slight improvement (measured!).

    I trust my ears now and simply love the result

    If you guys do need some more info, just ask and I'll try to answer.

  8. #8
    Senior Member
    Join Date
    Nov 2003
    Location
    Toronto
    Posts
    1,162
    Quote Originally Posted by Guido View Post
    Stop lamenting about TAD prices. Go get a pair. The TAD graph looks slightly smoother but can't really show the improvement. It's incredible how this dramatic 4435 low end combined with the TAD top end sounds. Uuuuhhhh
    I couldn't agree more Guido, my experience with TD 2002 has been nothing short of amazing. One thing I did note was a particularly long break-in period. They were good early on and continued to get better over a period of months.

  9. #9
    Administrator Robh3606's Avatar
    Join Date
    Apr 2003
    Location
    Rocinante
    Posts
    8,207
    Hello Guido

    Great! Thanks for posting it. Do you have the waterfalls for the finished systems??

    Rob
    "I could be arguing in my spare time"

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Pro Critical Remarks on the 4430 and 4435
    By mech986 in forum Lansing Product General Information
    Replies: 15
    Last Post: 08-08-2007, 01:53 PM
  2. Finally my new babes have arrived (4435)
    By baldrick in forum Lansing Product General Information
    Replies: 137
    Last Post: 01-22-2007, 08:45 PM
  3. 4430/B40 vs 4435
    By leif in forum Lansing Product General Information
    Replies: 50
    Last Post: 02-26-2006, 12:44 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •