if i have the messures i will finish :-) the box :-)
now i have the adapter ! (selfmade)
and the low driver will arrive tomorrow
the crossover will be finished tomorrow
greetings
if i have the messures i will finish :-) the box :-)
now i have the adapter ! (selfmade)
and the low driver will arrive tomorrow
the crossover will be finished tomorrow
greetings
PEM is a brand of captive or "self-clinching" nuts:
http://www.pennfast.com/fastening_pr...&df=next&sp=16
sorry ....sure.... i ment the height
OK Here we go with the points of the Dutch jury.
Take note: all measurements are in cm and of the left speaker (so mirror it if it's for the right one)
Bottom cabinet- center woofer: 34,5
Center woofer- Left side of cabinet: 32,5
Center woofer- Right side of cabinet: 24
Bottom cabinet- center of reflexpipe: 11,5
center of reflexpipe- left side of cabinet: 19,2
Upperside woofer- bottom of horn: 22
space on right side of the horn: 2
space on left side of the horn: 10
diameter reflexpipe: 11
length of reflexpipe: 14
Left woofer - right woofer : 320
Good luck
yeah very good yob !!!!
finally i need the height of the divider between the Horn/Bass
greetings !
Can you be more specific. Don't understand.:o
Take note: bottom of cabinet is not to the ground, but like the red line on your picture.
Hi Peterr,
Matthias is referring to the board inside the S2600 dividing the enclosure into 2 parts. It is located above the woofer and below the horn, and Matthias wishes to know its exact location.
De groetjes van Kopenhagen
thank you :-) Jan !
exactly !
the location of the midplate i need !
I'm afraid i can't help you at short notice. Have to take out the horn of woofer to see that. It will happen in the near future (some ajustments to the filter and removing the mesh in the horn), but not the next few weeks i'm afraid.
I think you have two questions
a. Is the board solid?
b. What is the exact location?
Question a. i could ask a friend of mine who took the 2600 apart in the past. for b. you have to have some patience. Sorry.
oh.. ok !
H Peterr - I see that you plan on removing the horn throat mesh. What is your reasoning on that? I once asked the question here and was told by most to just leave it alone. Comments like it was made to be used that way to what if a bug decides to take up residence inside the compression driver ! What think you ? As I will be taking my horn out today or tomorrow I would like to have your thoughts.Originally Posted by Peterr
Thanks - Bernard
PS - Mattias, if your listening, hope to have that measurment for you in a day or two.
Ok Matthias, here is the measurment. 15 5/8 " or 39.7 mm. I hope this is the same for the 2600 as the 3200. I was surprised to see that the back of the horn does have a thin layer of dampenig material sprayed on. I will be adding to it. Also, you might want to know that there are some braces running down both sides of the cab all the way to the top. If I had thought of bringing my digital camera home I might have gotten a pic for you.. but as it is I might have to close them up before I can get a pic for you. Tell me if you wish to know more about these braces.
Good luck
Bernard
oh thank you very much ! i think you meant 397mm or 39,7 cm !
is this the height of the cabinet in which is the horn placed ?
i think i dont need damping material ! because the mdf
greetings
Yes - 397mm. This the exact hieght from the inside top of the cab to the top of the dividing panel. Hope it is the same in the 2600! I am dampening my horn to isolate it from the back pressure wave/vibration of the bass driver. Don't think you will need that.Originally Posted by MatthiasA
Good Luck and let us see your progress.
Bernard
Hi Bernard,
- Are you now stating that the 3100 has a dividing panel in it that actually divides the enclosure into two separate air-tight compartments ?Yes - 397mm. This the exact hieght from the inside top of the cab to the top of the dividing panel.
- Or are you stating that your given measurement is down to the "brace" that the 3100s' horn/driver/bracket mounts onto ?
<. Earl K
PS ; I realize that you are likely using "mental-shorthand" ( assumed meanings ) for those ( like MatthiasA ) who have followed this thread from the beginning - the problem arises when others jump into the mddle of the conversation .
There are currently 1 users browsing this thread. (0 members and 1 guests)